供应TLD型预置扭矩起子

测力仪表价格：800.00元/个 有效期至：长期有效

1、可预设定扭矩值。
　　2、超过设定值起子空转。
　　3、左、右扭矩值均可控制。
　　4、精度度±5%。
　　5、可供规格：0.1－1.2N.m、 0.5－3N.m、1－6N.m。

Instruction
The torque wrenches （扭矩扳手）are used to tighten up, according to the requirement of torques, the screw thread fasteners (such as nuts and bolts).
Our company is one of the best torque wrenches manufacturers in the domestic market, boasting the most specifications of wrenches and the highest specialization in this field. All products in our company are produced strictly according to the national standards GB/T15729-1995. Moreover, our company installs all testing equipments and introduces all key spare parts from Japan, to promise the stable quality of all products. We have five main catalogues including over fifty specifications, especially BA, AC, TL presetting torque wrenches, TLB high precision testing torque wrenches, and TLD presetting torque screwdrivers. Besides, our company will also manufacture the torque wrenches against the special specification offered by our customers.
BA, AC, TL presetting torque wrenches
I Features.
1. having the presetting torque number and sentinel equipment. When a fastener's tightening torque reaches the pre-set number, the wrench will clatter and give an obvious feeling of shaking.
After releasing the acting force, the relevant spare parts can be automatically reset.
2. The shell of BA, AC is made of the best aluminum alloy, and the shell of TL is made of the special steel pipes.
3. TL torque wrench has a two-way ratchet wheel on the head, guaranteeing more convenient for use.
II use methods
1.According to the work requirement, set the presetting torque.
2.when presetting the torque number, please put the regulating key into the end of a wrench, and then revolve the key until the regulating scale mark reaches the torque number required. After that, just pull out the key. When you preset torque number for BA, please pull out the red plastic handle at the end of a wrench and then bend and wind it until the regulating scale mark reaches the torque number required. After that, replace the red plastic handle.
3.Please put a bushing onto the wrench as well as the fastener. And put your hand on the handle and gradually exert your stress until you hear "clatter", the signal of getting the preset torque number. now, you have finished your job.
4.if the wrench is not used for a long time, you'd better put the regulating scale mark to the minimum torque number.
III Technological Parameter
AB、AC presetting torque wrenches
IV Precautions
1.When using the wrenches, do not put strength too extremely or beyond the range of torque. After hearing the signal, please do release the applied force immediately.
2.The wrenches are needed to handle with care and should not be used as a hammer.
3.The wrenches should be kept in a dry place in case of rustiness.
4.when using the large wrenches, please use extension bars to connected with wrench handles to save strength.
TLB high precision testing torque wrenches
I. the scope of application
TLB is a meter indicator used to measuring any torques of the screw thread fasteners within the measurement range. TLB can be especially used on measuring torques of the fasteners required with high accuracy.
1.before using, please adjust the zero point in the first place
1)if you want to rotate wrenches to right，please spin the button on the panel in an anticlockwise way until the red driven needle and the black driving needle are getting closed; meanwhile, please rotate the shell to make the driven needle get to the zero point of the panel torque scale.
2)If you want to rotate wrenches to left, please spin the button on the panel in an clockwise way until the red driven needle and the black driving needle are getting closed; meanwhile, please rotate the shell to make the driven needle get to the zero point of the panel torque scale.
2.Please exert the strength slowly and smoothly until the needles get the required torque.
3.After stopping using the strength, the black driving needle will come back to the zero point and the red driven needle will still stay in the scale value indicated and the torque can be read accurately. If you turn the button on the panel, the red driven needle will come back to the zero point .
II Technological Parameter
III Precautions
1.Please do not knockdown or hit the wrenches at pleasure in case of doing harms to the accuracy.
2.The outer ring of the panel is made of plastic, so please do not get wrenches close to high temperature.
3.Do not get beyond the range of the torque values
4.The wrenches are not allowed to use for loosing fasteners in case that the overload will have bad effect on the accuracy.
TLD presetting torque wrenches
1.You can preset the torque value
2.if the torque value is beyond the range, the wrench will run idly.
3.the left and right torques can be both controlled
4.the accuracy is +/- 5%
5.the types provided: 0.1-1.2 n.m. 0.5 ----3 n.m. 1---6 n.m