布轮价格：6.00元/个 有效期至：长期有效
德国进口材料,台湾东升 品质超脱
| 精工细琢 专业品牌 | |||||||||||||||||||||||
| 树脂法研磨砂轮强度高弹性好,耐消耗, | 树 | ||||||||||||||||||||||
| 可作高转速研磨. | 脂 | ||||||||||||||||||||||
| 制法 | B法 | 法 | |||||||||||||||||||||
| 工件材质 | 研 | ||||||||||||||||||||||
| 一般钢材 | 素材 | 30A30KB | 磨 | ||||||||||||||||||||
| 已硬化处理 | WA36KB | 砂 | |||||||||||||||||||||
| 合金钢 | 素材 | WA36KB | 轮 | ||||||||||||||||||||
| 已硬化处理 | WA36JB | ||||||||||||||||||||||
| 工具钢 | 素材 | WA46IB | |||||||||||||||||||||
| 已硬化处理 | WA46HB | ||||||||||||||||||||||
| 不锈钢 | 400系列 | WA36JB | |||||||||||||||||||||
| 300系列 | WA36IB | ||||||||||||||||||||||
| 铸铁 | 一般铸铁 | C30KB | |||||||||||||||||||||
| 特殊铸铁 | GC36JB | ||||||||||||||||||||||
| KNGDOM 台湾东升专业砂布轮 高效 低耗 | |||||||||||||||||||||||
| 氧化铝纤维盘砂布轮 氧化锆纤维盘砂布轮 | |||||||||||||||||||||||
| 型号 | 尺寸 | 粒度 | |||||||||||||||||||||
| 40 | 60 | 80 | 100 | -400 | |||||||||||||||||||
| ZP100 | 100*16 | ● | ● | ● | ● | ● | |||||||||||||||||
| ZP115 | 115*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ZP125 | 125*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ZP150 | 150*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| ZP180 | 180*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| 型号 | 尺寸 | 粒度 | |||||||||||||||||||||
| 40 | 60 | 80 | 100 | -400 | |||||||||||||||||||
| AP100 | 100*16 | ● | ● | ● | ● | ● | |||||||||||||||||
| AP115 | 115*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| AP125 | 125*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| AP150 | 150*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| AP180 | 180*22 | ● | ● | ● | ● | ● | |||||||||||||||||
| 订购指南 精工细琢 专业品牌 | ||||||||||||
| WA | 46 | K | 5 | V | 5 | A | 350x40x127 | |||||
| 磨料 | 粒度 | 结合剂 | 组织号 | 制法 | 型状 | 缘形 | 尺寸(DxTxH) | |||||
| 磨料粒度: | Grit | |||||||||||
| 精度是用来表示磨料颗粒几何尺寸的大小,其选择 | Grit is designated to represent the geometrical size of | |||||||||||
| 依据主要是加工工件所需要的表面粗糙度,同时也需 | abrasive grain.The grit size is chosen for customer's | |||||||||||
| 考虑其他一些因素.以外圆磨为例,常用粒度与表面 | required surface finish as well as other conditions.For | |||||||||||
| 糙度有下面的大致关系: | example,in cylindricai grinding,there is relationship | |||||||||||
| between grit and surface finishes listed as bellow; | ||||||||||||
| 粒度 | 36-46 | 54-60 | 70-80 | 90-100 | Grit | 36-46 | 54-60 | 70-80 | 90-100 | |||
| 粗糙度 | Ra 1.6 | Ra 0.8 | Ra 0.4 | RA 0.2 | Finish | Ra 1.6 | Ra 0.8 | Ra 0.4 | RA 0.2 | |||
| ●粗料度的磨料适用于磨削: | ●Use Coarse Grit: | |||||||||||
| 1)材质较软,延伸率大以及类似软铁和有色金属等 | 1.for soft,ductile,stringy material such as softsteel | |||||||||||
| 材料 | and nonferrous material | |||||||||||
| 2)进给量大,磨削速度要求高的场合. | 2.for rapid stock removal,high grinding speed | |||||||||||
| 3)表面粗糙度要求不高的场合. | 3.where finish is not important | |||||||||||
| 4)磨削接触面大的场合. | 4.for large areas of contact | |||||||||||
| ●细粒度的磨料适用于磨削: | ●Use Fine Grit: | |||||||||||
| 1)硬度较高以及类似高碳工具钢,硬质合金钱类的金 | 1.for hard,brittle materials such as hard tool steels, | |||||||||||
| 属材料和玻璃等脆性材料. | cemented carbide and glass. | |||||||||||
| 2)表面粗糙度及精度要求高的场合. | 2.for fine finishes | |||||||||||
| 3)磨削接触面小的确场合. | 3.for small areas of contact | |||||||||||
| 4)工件半径或弧度小的场合. | 4.for holding small corner radii | |||||||||||
| 硬度: | Grade: | |||||||||||
| E F G H I J K L M N O P Q R | E F G H I J K L M N O P Q R | |||||||||||
| 软----------------------硬 | Soft------------------Hard | |||||||||||
| 砂轮的硬度是指磨料之间的结合度,砂轮中结合 | The grade indicates the relative holding power of the | |||||||||||
| 剂量的多少决定了砂轮的硬度大小.用户需根据具 | bond which holds abrasive grains in a wheel.ln general, | |||||||||||
| 本的磨削(如进刀量,粗糙度,材质)要求来灵活选 | with a given type of bond it is the mount of bond which | |||||||||||
| 择砂轮的硬度. | determines a wheel's should select the grade of a wheel | |||||||||||
| 一般砂轮硬度选择的原则是: | based on the grinding parameters such as feed rate. | |||||||||||
| finish requirements,materiials i.e..The following rules | ||||||||||||
| should be followed with regard to grade | ||||||||||||
| ●较软的硬度 | ●Use Soft Grade: | |||||||||||
| 1)进刀量大的粗磨. | 1.for rapid stock removal | |||||||||||
| 2)磨削接触面大的场合. | 2.for large greas of contact | |||||||||||
| 3)材质较硬的工件,如高硬度工具钢和硬质合金钢等. | 3.for hard materials such as hard tool steels and carbide. | |||||||||||
| 4)工件抗热性能差,严防表面烧伤和磨削. | 4.for heat sensitive workpieces and grinding can not has | |||||||||||
| burning and discoloration on surface | ||||||||||||
| ●较硬的硬度 | ●Use Hard Grade: | |||||||||||
| 1)进刀量小的精磨. | 1.for fine finish with little feed | |||||||||||
| 2)延长砂轮寿命. | 2.for longer wheel life | |||||||||||
| 3)材质较软的工件. | 3.for soft materials | |||||||||||
| 4)磨削接触面小或窄的场合. | 4.for small or narrow areas of contact | |||||||||||
| 组织号: 5 6 7 8 9 10 11 12 13 | Structure: | 5 6 7 8 9 10 11 12 13 | ||||||||||
| 密--------------- 疏 | Close------------Open | |||||||||||
| 组织号用以表示砂轮内相邻的磨料颗粒之间的距 | The structure number indicates the space between neighboring | |||||||||||
| 离也就是间隙的大小.砂轮中磨料颗粒所占的体积百 | grains which can also be called grain spacing in a wheel The | |||||||||||
| 分比,也就是其浓度的大小,决定的砂轮的组织号.陶 | volume percentage of abrasive grains which represents the | |||||||||||
| 瓷砂轮组织号变化范围一般是从5到13,数字越小表 | density of grain in a wheel determines the structure number | |||||||||||
| 示砂轮组织越密,数字越大表示砂轮组织越疏松.组 | of a wheel.The structure of Vitrified sheels ranges from 5 to | |||||||||||
| 织11,12和13通常是指气孔砂轮. | 13.The smaller the number,the more closed structure the wheel | |||||||||||
| The large the number,the more open structure wheel The numbers | ||||||||||||
| 11.12.13normally indicate porous wheels. | ||||||||||||
| 型号 | PW | 规格 | 40*10 |
| 材质 | PW | 外径 | 0（mm） |
| 转速 | 0（r/min） | 适用范围 | 适用于一般金属，焊接缝等 |
本文引用地址：http://www.worldmetal.cn/sell/show-494544-1.html
以上"供应台湾东升超强不织布轮"信息由企业自行提供，该企业负责信息内容的真实性、准确性和合法性。本网对此不承担任何保证责任。
以上"供应台湾东升超强不织布轮"信息由企业自行提供，该企业负责信息内容的真实性、准确性和合法性。本网对此不承担任何保证责任。
